16841
Parts / Onderdelen
!

Mercury 2.5, 3.3, 3.5 (4s)

!

Propellers / Schroeven for / voor Mercury & Mariner 2.5, 3.3 en 3.5 (4s).

This is the same engine as Tohatsu 2.5 and 3.5, propellers wil also fit on these engines. Deze is dezelfde motor als de Tohatsu 2.5 en 3.5, schroeven passen dus ook op deze motoren.

shear pin

Drive Pin/Shear Pin / Breekpen

17-815111Q02
!

For / voor 2.5, 3.3 & 3.5 (4s)

Setje van 3 stuks

cotterpin

Cotter pin / Splitpen

18-95295Q
!

For / voor 2.5, 3.3 & 3.5 (4s)

Setje van 3 stuks

Mercury 4-6

!

This propellers fit Mercury and Mariner 4, 5, F4, F5 and F6 models. / Deze schroeven passen op Mercury en Mariner 4, 5, F4, F5 en F6 modellen.

This is the same engine as Tohatsu 4, 5 and 6, propellers wil also fit on these engines. Deze is dezelfde motor als de Tohatsu 4, 5 en 6, schroeven passen dus ook op deze motoren.

thrust washer 456

Thrust Washer

16145Q01
!
First ring on the propshaft, in front of the propeller.
aft prop washer 456

Aft Propeller Washer

12-16146Q
!
Washer between the nut and the propeller
nut 456

Nut

16147Q
!
cotterpin 456

Cotter pin

18-815026Q
!
Setje van 3 stuks

Mercury 6-15

!

Propellers for Mercury and Mariner 6 (2S), 8 (2S and 4S up to 2004), 9.9 (2S and 4S up to 2004), 10, 13.5 and 15 (2S and 4S up to 2009). Propeller will only fit on Mercury made motors, some engines are made by Yamaha (old Mariner's) and Tohatsu (mostly the newest 4S as well as some commercial engines), propeller will not fit! Not for Bigfoot!

Schroeven voor Mercury en Mariner 6 (2T), 8 (2T en 4T tot 2004), 9.9 (2T en 4T tot 2004), 10, 13.5 en 15 (2S en 4T tot 2009). Schroef past alleen op motoren gamaakt door Mercury, sommige motoren zijn gemaakt door Yamaha (oude Mariner's) en Tohatsu (vooral de nieuwste 4T alsook sommige commerciele motoren), schroeven zullen hier niet op passen! Niet voor Bigfoot!

Flo-Torq I Hub

827598T
!
Flo-Torq I Round Rubber Hub
Extremely difficult to replace!

Prop Nut Kit

13914Q02
!
822559q01

High reverse thrust kit

822559Q01
!
Inceases the reverse thrust very much!
11-40140

Mercury propeller nut

11-40140
!
Brass prop nut M10 x 1.5
23-420911

Mercury propeller spacer

23-42091 1
!
Spacer between propeller and propeller nut.

Thust washer

821932
!
Thrust washer for newer engines, outer diameter of 1,39"/3,53 cm

Thrust washer newest model

821932 1
!
Thrust washer for the newest engines, outer diameter of 1,51".3,84cm

Mercury 7.5 & 9.8

!

Propellers for / Schroeven voor Mercury 75, 7.5, 110 & 9.8. 1968 - 1985

8 spline as.

Propeller nut kit with rings

11-64075A1
!

Nut, ring and special ring, all hardware that comes after the propeller. Also for 4 & 4.5 hp (aluminium cowl).

Mercury F8 & F9.9

!

Propeller fits / Schroef past op Mercury & Mariner F8, F9.9.

Also 6 (2 cyl), 8 & 9.9 hp that are build by Tohatsu under Mercury, Mariner and Tohatsu brand.

Schroef past ook op 6 (2 cil), 8 & 9.9 pk die gebouwd zijn door Tohatsu onder de merknaam Mercury, Mariner en Tohatsu.

Forward thrust washer

803743002
!

First ring on propellershaft, in front of the propeller

12-16146

Aft washer

12-16146Q
!
Ring between propeller and nut
11-16147

Propeller nut

16147Q
!
18-815026

Cotter pin

18-815026Q
!

Mercury 9.9 - 25, 3-1/4" gearcase/staart

!

Propellers for Mercury and Mariner 9.9 Bigfoot (up to 2004, 323 cc), 15 Bigfoot (up to 2009), 18 (old), 20 (2-stroke) and 25 (2-stroke), all are Mercury made motors (9.9 and 15 have Yamaha powerheads). Also for Force 25 hp 1995-1998. Will not fit on Tohatsu made motors!

Schroeven voor Mercury en Mariner 9.9 Bigfoot (tot 2004, 323 cc), 15 Bigfoot (tot 2009), 18 (oud), 20 (2-takt) and 25 (2-takt), allen zijn motoren gemaakt door Mercury (9.9 en 15 hebben een Yamaha motorblok). Ook voor Force 25 pk 1995-1998. Past niet op door Tohatsu gemaakte motoren! 

11-88228

Propeller nut

11-88228
!

Made from plastic.

Standard delivered with the engine.

858498

Forward thrust washer

858498
!
First ring on the propeller shaft, in front of the propeller.
11-40119 12

Brass propeller nut

11-40119 12
!
Made from brass.
rubber hub

Flo Torq I round rubber hub

19669T
!
Extremely difficult to install!

Mercury 9.9BF-20

!

This propellers fits Mercury and Mariner F9.9 bigfoot (2005 and newer), F15 and F20 2008 and newer. Also fit 15 hp 2-stroke (international, serialnumber start with 0N.) All those engines are Tohatsu build. Propeller will also fit Tohatsu 9.9, 15, 18 and 20 hp.

Deze schroeven passen op Mercury en Mariner F9.9 Bigfoot (2005 en nieuwer), F15 en F20 2008 en nieuwer. Past ook op 15 pk 2-takt (international, serienummer begint met 0N.) Al deze motoren zijn door Tohatsu gemaakt. Schroeven passen ook op Tohatsu 9.9, 15, 18 en 20 pk.

Forward thrust washer

803743
!

First ring on propeller shaft, in front of the propeller.

12-16146

Aft Washer

12-16140 2
!
Ring between propeller and nut.
11-16147

Propeller nut

11-16147Q
!
18-815026

Cotter pin

18-815026Q
!
rubber hub

Flo Torq rubber hub

8m0054769
!
Extremely difficult to install!

Mercury 25 & 30, 3-1/4" gearcase/staart

!

Propellers for Mercury and Mariner 25 and 30 hp, Four stroke EFI 3 cylinder, and also 2-stroke international versions 430cc (serial numbers start with 0N.), all those engines are Tohatsu build. Will also fit Tohatsu brand engines of the same models.

Schroeven voor Mercury en Mariner 25 en 30 pk, 4-takt EFI 3 cilinder, en ook de 2-takt international versies 430cc (serienummer begint met 0N.), al deze motoren zijn gemaakt door Tohatsu. Passen ook op Tohatsu-merk motoren.

18-815026

cotter pin

18-815026Q
!
12-16146

Aft washer

12-16140
!
Ring between propeller and nut
hub

Flo-Torq I hub

897001T
!
Extremely difficult to replace
11-16147

Propeller nut

16147Q
!

Mercury 25-70, 3-1/4" gearcase/staart

!

This propellers will fit on Mercury and Mariner 25 4-stroke Bigfoot, and 30, 35, 40, 45, 50, 55 and 60 hp, both 2- and 4-stroke, non-Bigfoot. And old 70 hp till 1983. All are only Mercury made outboards (some 4-strokes have Yamaha powerheads). Also Force 40-50 1995-1998, 70 1991-1995 en 75 1996-1998.

Deze schroeven passen op Mercury en Mariner 25 4-takt Bigfoot, en 30, 35, 40, 45, 50, 55 en 60 pk, zowel 2- als 4-takt, geen Bigfoot. En oude 70 pk tot 1983. Al deze motoren zijn door Mercury gemaakt (enkele 4-takt hebben Yamaha motorblokken). Ook Force 40-50 1995-1998, 70 1991-1995 en 75 1996-1998.

Diffuser ring

68861T
!
To prevent the exhaust gasses to come in contact with the propeller, for aluminium propeller only.

Propeller nut kit

11-69578Q 1
!
Contains a self locking nut with the tab washer and a spare tab washer.

Propeller hardware kit

11-31990Q02
!
Contains the first ring, the tab washer and the self locking nut. Complete hardware kit.
tab washer

Tab washer

14-76281Q
!
Setje van 2 stuks

Thrust washer

73345A 1
!
First ring on the propeller shaft, in front of the propeller

Rubber hub

43676T
!
Rubber hub, very difficult to install
trim tab 31640

Trim tab

31640Q 4
!

Aluminium

Check for adequate propeller clearance prior to operation.

trim tab 822777

Trim tab

822777Q 1
!

Aluminium

For applications where extra clearance is required for high rake propellers.

Anodic plate

76214Q 5
!

Aluminium

Provides additional clearance for high rake propellers

849505 1
!

To protect your propeller as well as to prevent sharp edges, looks great!

Maximum diameter 11 inch

Flo-Torq Reflex hub kit

835257Q12
!
Comes complete with thrust washer, lockwasher and nut.

Mercury 350/450/500/500SS

!

Propellers for (old) Mercury 350, 450, 500 and 500SS, 11 spline hub.

Schroeven voor (oude) Mercury 350, 450, 500 en 500SS, 11 spline bus.

38859a-1

Thrust hub

38859A 1
!
First ring on the shaft
12-32007

Washer

12-32007
!
Washer between propeller and nut

Nut

11-69578Q1
!

Mercury 40-125

!

This propellers will fit Mercury and Mariner 40 Bigfoot, 50 Bigfoot, 60 Bigfoot, 65 (4-cil), 70, 75, 80, 85, 90, 100, 115, 125 and 150(non V6) 2-stroke, Optimax and 4-Stroke.

Deze schroeven passen op Mercury en Mariner 40 Bigfoot, 50 Bigfoot, 60 Bigfoot, 65 (4-cil), 70, 75, 80, 85, 90, 100, 115, 125 en 150 (niet V6) 2-takt, Optimax and 4-takt.

Mercury V6 + Mercruiser

!

This propellers will fit Mercury and Mariner V6 outboards as well as all Verado outboards. Only exception is the 225 4-stroke build by Yamaha. Propellers will also fit all Mercruiser Alpha and Bravo One drives.

Deze schroeven passen op Mercury en Mariner V6 buitenboordmotoren alsook Verado motoren. Enige uitzondering is de 225 4-takt die door Yamaha is gemaakt. Schroeven passen ook op de Mercruiser Alpha en Bravo One aandrijvingen.

FLO-TORQ II HUB KIT MERCURY 40+

835257Q 1
!

Complete hub kit that is standard with many Genuine Mercury propellers.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

FLO-TORQ II HUB KIT HONDA 75-90 OUD

835277Q 1
!

Honda outboards (75-90 HP thru 1998)

Inhoud:

12-835467 1 Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

14-816629Q Tab lock washer

11-827614 Prop nut

FLO-TORQ II HUB KIT HONDA 75-130 NIEUW

835279Q 2
!

Honda buitenboordmotoren (75-90 PK 1999-en nieuwer, 115-130 HP)

Inhoud:

12-853359 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Washer

859939 Lock

18-47959 Cotter pin

FLO-TORQ II HUB KIT HONDA 135+

835278Q 1
!

Honda 135, 150, 175, 200 en 225 PK 4-Takt. Past ook op Mercury Racing propellers.

Inhoud:

12-888451 Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT OMC - Volvo-Penta

835270Q 1
!

OMC Cobra/Volvo SX sterndrives (19 tooth spline, 1994-present)

Caution! When installing stainless steel propellers, remove the anode to bearing

carrier and check clearance before operation.

Inhoud:

12-835467 7 Forward thrust washer

835290A1 Plastic drive sleeve

850330Q Aft adaptor

879143 Spacer

802126Q 1 Nut

Cotter pin included with Nut

FLO-TORQ II HUB KIT EVINRUDE, JOHNSON & OMC NIEUW

835265Q02
!

Evinrude, Johnson outboards & OMC stern drive (V-6 & V-8 staart, 1991 & Nieuwer

incl. new 250 HP V-6 outboard en 2003 V-6 met Cresent staart). Past ook op Mercury Racing propellers.

Inhoud:

12-835467-008 Forward thrust washer, 835290A1 Plastic drive sleeve, 834899Q Aft

adaptor, 12- 887972 Aft Washer, 802009Q1 Nut, Cotter pin and spacer

FLO-TORQ II HUB KIT EVINRUDE, JOHNSON & OMC -1990

835267Q 1
!

Evinrude/Johnson, OMC stern drives (V-6 & V-8 staart, 1984-1990)

Inhoud:

12-835467 1 Forward thrust washer

835290A1 Plastic drive sleeve

834899Q Aft adaptor

802009Q 1 Nut Kit

(Cotter pin and spacer included with Nut kit)

FLO-TORQ II HUB KIT EVINRUDE & JOHNSON V4

835266Q 1
!

Evinrude & Johnson buitenboordmotor (V-4 staart, 1968-en nieuwer) Use only with Quicksilver Propellers (QS5136H, QS5138H, QS5140H, QS5142H, QS5144H propellers have a small diameter labyrinth seal)

Inhoud:

859915 Thrust washer

835290A 1 Plastic drive sleeve

834839Q Aft adaptor

859929 Nut

18-89961 Cotter pin

FLO-TORQ II HUB KIT SUZUKI/JOHNSON 90-115 4T

835283Q 1
!

Johnson & Suzuki 90-115 HP 4-takt buitenboordmotor

Bestaat uit:

12-888939 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q1 Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI/JOHNSON 140 4T

835283Q 2
!

Johnson & Suzuki 140 HP 4-takt buitenboordmotor

12-835467 1 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q1 Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI 60-140

835282Q 1
!

Suzuki 60 PK 4-Takt (1998 en nieuwer) 70 PK 4-Takt (1998-2008) 75-140 PK 2-takt

Inhoud:

12-854621 Fwd thrust washer

835290A1 Plastic drive sleeve

834839Q Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI 150+

835281Q 1
!

Suzuki 150-225 PK 2-Takt buitenboordmotoren en 150-250 PK 4-Takt buitenboordmotoren. Kan

worden gebruikt met Mercury Racing propellers.

Inhoud:

12-853359 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-31211A3 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI DF70-90

835283Q03
!

Suzuki 70-90 PK 2009 en nieuwer

12-8M80042329 Fwd thrust washer

835290Q 1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT TOHATSU

835284Q 1
!

Tohatsu/Nissan (70C, 90-140 PK)

Inhoud:

12-853948T Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q1 Aft adaptor

12-16140 Washer

11-16147 Nut

18-815026 Cotter Pin

FLO-TORQ II HUB KIT YAMAHA 50-100

835272Q 1
!

Yamaha buitenboordmoteren (50-100 PK, splines in het voorste drukring)

Inhoud:

12-853555Q Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-850076 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT YAMAHA V4-V6 2T

835271Q 2
!

Yamaha buitenboordmotoren & inboards (V-4 & V-6 staart, 1980-nieuwer), exclusief de 4-takt. Past ook op Mercury Racing propellers.

Inhoud:

12-853948T Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-850076 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT YAMAHA F150+

835274Q 1
!

150, 200 & 225EFI PK(4-TAKT) Yamaha of 225 (4-TAKT) Mercury

853948 1 Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II MET BUS MERCURY 40+

835257Q 6
!

Same as normal Flo-Torq II, but then with the bushing 23-856163A1.

The propeller is stronger attached to the shaft, for applications when the propeller is not fully submerged in the water (high engine mounted).

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

FLO-TORQ II SOLID HUB KIT NORMAAL 1"

835258Q 1
!

This solid hub is specially designed for Chopper, Cleaver, Lightning E.T., Pro E.T. and old style Bravo I (with MerCruiser logo) propellers.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

FLO-TORQ II SOLID HUB KIT NORMAAL 1"

835258Q 2
!

Standard length hub for use with the Fury, Tempest Plus, Mirage Plus, REV 4, Trophy

Plus, Bravo I & Maximus propellers (Bravo One Sterndrive 400HP+, 1" prop shaft).

FLO-TORQ II HD SOLID HUB KIT DIK 1,25"

840389Q06
!

Bestaande uit:

840382A02 black snubber strip replacement kit

840383A 2 prop nut & washer kit

For use with HD (Heavy Duty) 1.25" propshaft when installed on Mercury Racing

200XS, 225X, 2.5 EFI, 225 (Pro X, Pro XS, Sport XS), 250 (XS, Pro XS, Sport XS),

300 (X, XS), Sport, Torque and HD Fleet Master gearcases (not Fleet Masters with

1" propshafts) and MerCruiser Bravo One XR or XZ,Sport Master and shorty Sport

Master sterndrives.

flotorqii

FLO-TORQ III HUB KIT MERCURY 40-125

835257Q 9
!

Special hub kit (complete). Specially designed to reduce the clunck when you shift in gear, specially developed for the quiet four stroke engines.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

The drive sleeve is half made of hard plastic rubber and the aft adaptor is longer than the normal hub kit.

FLO-TORQ III HUB KIT YAMAHA 50-100

835272Q09
!

Yamaha buitenboordmotoren (50-100 PK, splines in voorste drukring)

Inhoud:

12-853555Q Forward thrust washer

881940A 1 Drive Sleeve Assembly

878584 Aft adaptor

12-850076 Spacer

859939 Nut

18-47959 Cotter Pin

flotorqiii

FLO-TORQ IV HUB KIT MERCURY 135+

835257Q10
!

Specially designed for quiet four stroke engines (Verado 135 hp and up), however will fit any V6 gearcase.

Will reduce the clung/rattle while shifting. Is a stronger version of the Flo Torq III that is used on 40 to 115 hp engines.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

Drive sleeve for Flo-Torq III

881940Q 1
!

Drive sleeve is half made of hard plastic, and half of soft rubber.

Part of Flo-Torq III hub kit.

rubber hub1

Rubber hub old

17611T
!

Fixed rubber hub for Flo-Torq I propellers.

For stainless steel propellers.

Extremely difficult to install!

rubber hub

Rubber Hub old

52-42672T
!
Rubber hub for stainless steel Chopper and Lighning ET propellers
skeg

Replacement skeg

15985A02
!

Precision die cast 360XK alloy for stronger, more uniform welds.

Be careful while welding!

Diffuser ring

68858T
!
For the Aluminium Black Max propellers. A replacement for if your ring is broken.
anode 822777q1

Trim Tab anode for extra clearance

822777Q 1
!
If you need additional clearance with you current anode because of your high rake propeller, you probably need this trim tab anode instead of the standard trim tab.

Anodic plate for additional clearance

76214Q 5
!
This anodic plate gives you the additional clearance you need with high rake propellers. With this plate you have no trim tab anymore! Is standard on most engines with power steering.
anode 31640q 4

Standard Trim Tab anode

31640Q 4
!
This is the standard anode trim tab installed on most engines without power steering.
propshaft anode

Propshaft anode

809664A1
!

Helps to protect your drive against galvanic corrosion! Great if you add a stainless steel propeller! Comes complete with the replacement propellernut and the retaining bolt for the anode.

continuity washer 42351 1

Continuity Washer

13-42351 1
!

To install under the aft washer (Flo Torq I) or under the drive sleeve (Flo Torq II and higher) to have full continuity between the propeller and the propellershaft/engine.

This in order to protect you engine against galvanic corrosion.

Propeller nut kit (hardware kit) old

11-827614Q04
!

Use this kit for propellers with a Flo-Torq I hub (rubber, permanent hub).

Do not use with Flo-Torq II or newer (removable hub kits).

propnutkit1

Prop nut kit (nut + tab washers)

11-52707Q 1
!
1 propeller nut and 2 tab washer (1 for now and one spare)
tabwasher

Tab washer

14-816629Q
!
To lock the propeller nut
pvs-solid

Solid PVS vent fitting

19-889725
!
Solid Vent plug to fully close the PVS hole(s) in the PVS equipped propeller.

Washer old

12-31211Q03
!

This washer is only used with Flo Torq I propellers (with rubber hubs, not with removable hubs (Flo Torq II and higher))

This washer comes after the propeller and under the tab washer (and nut).

Aft adaptor Flo-Torq II

826074Q 1
!
This is the adaptor that is installed in the propeller from the aft side. It is part of the Flo-Torq II hub kits.

Aft adaptor - drive sleeve for Flo Torq IV

878584Q 1
!
Drive sleeve for in Flo Torq IV

Replacement Flo-Torq II sleeve

835290Q 1
!

Replacement sleeve for Flo-Torq II, for if your sleeve is broken when you hit an underwater object.

Always carry a spare sleeve while boating!

Replacement Flo Torq IV sleeve

896233Q01
!

This sleeve will break if you hit an object, have always a spare with you!

forwardbushing_thumb

Bushing for Flo-Torq II with bushing

23-856163Q 1
!

This bushing is standard in Flo-Torq II hub kit with bushing 835257Q 6.

Bushing comes in front of the sleeve.

With this bushing your propeller is stronger attaged to the propeller for surface applications.

thrustwasher

Forward thrust washer Flo-Torq II+

12-835467Q01
!

The first ring on the propeller shaft.

V6 en MerCruiser Alpha en Bravo One alsook de voorlopers MC-I en TRS alle nomale schroeven FloTorq 1, 2, 3 en 4 (vaste en verwisselbare bus).

3-4 Cilinder alleen Flo Torq 2 en 3 (verwisselbare bus).

Thrust Washer old

13191Q01
!

First ring on the propeller shaft

Alleen voor 3-4 cilinder (40 Bigfoot, 50 Bigfoot, 60 Bigfoot, 70 tot 125 pk) met FloTorq 1 (vaste rubberen bus).

Vent Plug

19-824431
!

 

pvs-small

PVS vent fitting small

19-889725T28
!
Vent plug to open the PVS a little in the PVS equipped propeller.
pvs-medium

PVS vent fitting medium

19-889725T35
!
Vent plug to open the PVS a medium size in the PVS equipped propeller.
pvs-large

PVS vent fitting large

19-889725047
!
Vent plug to open the PVS a large size in the PVS equipped propeller.
ventpluglaseriiold

Vent plugs for old Laser II RH

19220A 4
!

To block the ventilation holes in older Laser II propellers

Old A41 and A45 suffix propellers Right hand rotation propellers.

ventpluglaseriiold

Vent plugs for old Laser II LH

816318A 4
!

This vent plugs is to plug off the vent holes in older Laser II propellers.

For Left hand rotation propellers. Old A41 and A45 suffix propellers.

plug 824431

Vent plug Trophy old

19-824431
!

For older Trophy propellers (A41 and A45 suffix).

For sale per piece, you need 4 pieces, so order 4 pieces.

Replaces welch plug 19-32652A1.

plugs 855267a1

Vent plug Tempest old

19-855267A 1
!
To plug the Tempest propeller vent holes, oly for A40, A41 and A45 suffix propellers

Diffuser ring

45676T
!

New Diffuser ring that prevents the exhaust to flow in the propeller blades

Replacement for Black Max propellers

skeg1

Replacement skeg

859447A 1
!
To weld on your gearcase

Rubber Hub round

43615T 1
!

Replacement rubber hub for Flo Torq I

Round. Is extremely difficult install!

Square rubber hub

43647T
!

For replacement of the square rubber hub.

Is extremely difficult to install!

Mercury Phantom black spraypaint

92-802878Q 1
!
For you Mercury/Mercruiser drive/gearcase.

Mercury EDP Propeller Black Paint

92-802878Q50
!
340 gram spray can

Mercury 2-4-C Marine lubricant with teflon / Teflonvet

92-802859Q1
!
To lubricate propeller shaft. / Om de schroefas mee te smeren.

Propeller Cover

849492T01
!

To protect your propeller as well as to prevent sharp edges, looks great!

Maximum diameter 15 inch

propstow2

Prop Stow

847314A 1
!
To stow your propeller!
propstow

Prop stow large

93-824423 2
!
To stow your propeller!

FLO-TORQ II HUB KIT MERCURY 40+

835257Q 1
!

Complete hub kit that is standard with many Genuine Mercury propellers.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

FLO-TORQ II HUB KIT HONDA 75-90 OUD

835277Q 1
!

Honda outboards (75-90 HP thru 1998)

Inhoud:

12-835467 1 Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

14-816629Q Tab lock washer

11-827614 Prop nut

FLO-TORQ II HUB KIT HONDA 75-130 NIEUW

835279Q 2
!

Honda buitenboordmotoren (75-90 PK 1999-en nieuwer, 115-130 HP)

Inhoud:

12-853359 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Washer

859939 Lock

18-47959 Cotter pin

FLO-TORQ II HUB KIT HONDA 135+

835278Q 1
!

Honda 135, 150, 175, 200 en 225 PK 4-Takt. Past ook op Mercury Racing propellers.

Inhoud:

12-888451 Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT OMC - Volvo-Penta

835270Q 1
!

OMC Cobra/Volvo SX sterndrives (19 tooth spline, 1994-present)

Caution! When installing stainless steel propellers, remove the anode to bearing

carrier and check clearance before operation.

Inhoud:

12-835467 7 Forward thrust washer

835290A1 Plastic drive sleeve

850330Q Aft adaptor

879143 Spacer

802126Q 1 Nut

Cotter pin included with Nut

FLO-TORQ II HUB KIT EVINRUDE, JOHNSON & OMC NIEUW

835265Q02
!

Evinrude, Johnson outboards & OMC stern drive (V-6 & V-8 staart, 1991 & Nieuwer

incl. new 250 HP V-6 outboard en 2003 V-6 met Cresent staart). Past ook op Mercury Racing propellers.

Inhoud:

12-835467-008 Forward thrust washer, 835290A1 Plastic drive sleeve, 834899Q Aft

adaptor, 12- 887972 Aft Washer, 802009Q1 Nut, Cotter pin and spacer

FLO-TORQ II HUB KIT EVINRUDE, JOHNSON & OMC -1990

835267Q 1
!

Evinrude/Johnson, OMC stern drives (V-6 & V-8 staart, 1984-1990)

Inhoud:

12-835467 1 Forward thrust washer

835290A1 Plastic drive sleeve

834899Q Aft adaptor

802009Q 1 Nut Kit

(Cotter pin and spacer included with Nut kit)

FLO-TORQ II HUB KIT EVINRUDE & JOHNSON V4

835266Q 1
!

Evinrude & Johnson buitenboordmotor (V-4 staart, 1968-en nieuwer) Use only with Quicksilver Propellers (QS5136H, QS5138H, QS5140H, QS5142H, QS5144H propellers have a small diameter labyrinth seal)

Inhoud:

859915 Thrust washer

835290A 1 Plastic drive sleeve

834839Q Aft adaptor

859929 Nut

18-89961 Cotter pin

FLO-TORQ II HUB KIT SUZUKI/JOHNSON 90-115 4T

835283Q 1
!

Johnson & Suzuki 90-115 HP 4-takt buitenboordmotor

Bestaat uit:

12-888939 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q1 Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI/JOHNSON 140 4T

835283Q 2
!

Johnson & Suzuki 140 HP 4-takt buitenboordmotor

12-835467 1 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q1 Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI 60-140

835282Q 1
!

Suzuki 60 PK 4-Takt (1998 en nieuwer) 70 PK 4-Takt (1998-2008) 75-140 PK 2-takt

Inhoud:

12-854621 Fwd thrust washer

835290A1 Plastic drive sleeve

834839Q Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI 150+

835281Q 1
!

Suzuki 150-225 PK 2-Takt buitenboordmotoren en 150-250 PK 4-Takt buitenboordmotoren. Kan

worden gebruikt met Mercury Racing propellers.

Inhoud:

12-853359 Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-31211A3 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT SUZUKI DF70-90

835283Q03
!

Suzuki 70-90 PK 2009 en nieuwer

12-8M80042329 Fwd thrust washer

835290Q 1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Washer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT TOHATSU

835284Q 1
!

Tohatsu/Nissan (70C, 90-140 PK)

Inhoud:

12-853948T Fwd thrust washer

835290A1 Plastic drive sleeve

826074Q1 Aft adaptor

12-16140 Washer

11-16147 Nut

18-815026 Cotter Pin

FLO-TORQ II HUB KIT YAMAHA 50-100

835272Q 1
!

Yamaha buitenboordmoteren (50-100 PK, splines in het voorste drukring)

Inhoud:

12-853555Q Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-850076 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT YAMAHA V4-V6 2T

835271Q 2
!

Yamaha buitenboordmotoren & inboards (V-4 & V-6 staart, 1980-nieuwer), exclusief de 4-takt. Past ook op Mercury Racing propellers.

Inhoud:

12-853948T Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-850076 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II HUB KIT YAMAHA F150+

835274Q 1
!

150, 200 & 225EFI PK(4-TAKT) Yamaha of 225 (4-TAKT) Mercury

853948 1 Forward thrust washer

835290A1 Plastic drive sleeve

826074Q 1 Aft adaptor

12-887972 Spacer

859939 Nut

18-47959 Cotter Pin

FLO-TORQ II MET BUS MERCURY 40+

835257Q 6
!

Same as normal Flo-Torq II, but then with the bushing 23-856163A1.

The propeller is stronger attached to the shaft, for applications when the propeller is not fully submerged in the water (high engine mounted).

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

FLO-TORQ II SOLID HUB KIT NORMAAL 1"

835258Q 1
!

This solid hub is specially designed for Chopper, Cleaver, Lightning E.T., Pro E.T. and old style Bravo I (with MerCruiser logo) propellers.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

FLO-TORQ II SOLID HUB KIT NORMAAL 1"

835258Q 2
!

Standard length hub for use with the Fury, Tempest Plus, Mirage Plus, REV 4, Trophy

Plus, Bravo I & Maximus propellers (Bravo One Sterndrive 400HP+, 1" prop shaft).

FLO-TORQ II HD SOLID HUB KIT DIK 1,25"

840389Q06
!

Bestaande uit:

840382A02 black snubber strip replacement kit

840383A 2 prop nut & washer kit

For use with HD (Heavy Duty) 1.25" propshaft when installed on Mercury Racing

200XS, 225X, 2.5 EFI, 225 (Pro X, Pro XS, Sport XS), 250 (XS, Pro XS, Sport XS),

300 (X, XS), Sport, Torque and HD Fleet Master gearcases (not Fleet Masters with

1" propshafts) and MerCruiser Bravo One XR or XZ,Sport Master and shorty Sport

Master sterndrives.

flotorqii

FLO-TORQ III HUB KIT MERCURY 40-125

835257Q 9
!

Special hub kit (complete). Specially designed to reduce the clunck when you shift in gear, specially developed for the quiet four stroke engines.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)

The drive sleeve is half made of hard plastic rubber and the aft adaptor is longer than the normal hub kit.

FLO-TORQ III HUB KIT YAMAHA 50-100

835272Q09
!

Yamaha buitenboordmotoren (50-100 PK, splines in voorste drukring)

Inhoud:

12-853555Q Forward thrust washer

881940A 1 Drive Sleeve Assembly

878584 Aft adaptor

12-850076 Spacer

859939 Nut

18-47959 Cotter Pin

flotorqiii

FLO-TORQ IV HUB KIT MERCURY 135+

835257Q10
!

Specially designed for quiet four stroke engines (Verado 135 hp and up), however will fit any V6 gearcase.

Will reduce the clung/rattle while shifting. Is a stronger version of the Flo Torq III that is used on 40 to 115 hp engines.

Past op Mercury/Mariner 40 Bigfoot en groter (alleen door Mercury gemaakte motoren) en op MerCruiser Alpha en Bravo One alsook de voorlopers hiervan (MC-I en TRS)